What are the characteristics of a good Degreaser? It is a very important question as the asnwer to this question helps the consumers realize if to buy a degreasers or to reject it. Knowing the characteristics of a degreaser is very important as it helps rate a chemical degreaser. RXSOL Degreaser is one of the most demanded degreasers in Mumbai, Gandhidham, Mundra, Kandla, Kolkata, Howrah, Vishakhapatnam, Tuticorin, Chennai, India, UAE, Gulf, Canada. RX Marine International is one of the largest manufatcurers and suppliers of degreasers in Mumbai, Nhava Sheva, JNPT, Maharashtra, India. We also manufacturers and suppliers of Degreasers in Gandhidham, Kandla, Mundra, Bahruch, Kutch, Gujarat.
Know the characteristics of a good degreasers. The best option for you is to buy one of RXSOL Degreasers which are the best degreasers and come under the category of not good but best degreasers. All the characteristics of a great degreaser are present in RXSOL Degreasers. Therefore, instead of looking for degreasers all over the Internet, contact RX Marine International: manufacturer and supplier of best degreasers in India, UAE and Canada. Our humongous customer base has been constantly appreciating the quality of our degreasers and regarding it as one of the best degreasers in the market. Such are the sayings of players from Marine and Industrial chemicals field.
Below mentioned are some of the characteristics of a good degreaser.
Characteristics of a good degreaser :
- It is cost effective, easy to apply and use.
- High emulsification on mineral oils and petroleum based chemicals.
- Safe to use on most metal surfaces, painted surfaces and tank coatings.
- Cleans oil coolers, fuel oil pre heaters and lube oil heat exchangers.
- Removes general oil contamination from machinery and engine room.
- Economical cost effective.
- Used as a multi-purpose degreaser in extremely hard cleaning conditions
Contact us to buy the best degreasers in India, UAE, Canada
Mail us at: 123@rxmarine.com. RX Marine International is one of the largest manfacturers and suppliers of Degreasers in Kolkata, Howrah, Paradip, Haldia, West Bengal, India. RX Marine International also has made a strong foothold in Andhra Pradesh and we are manufacturers and suppliers of Degreasers in Vishakhapatnam. We also manufatcure degreasers in Chennai, Tutcorin. You can even contact us to buy degreasers in Dubai, Fujairah, Sharjah, Oman, Muscat, Kuwait, UAE, Gulf and Canada.
Coldwash is specified marine degreasing and Cleaning Chemicals. Cold wash Cleaning application in Maintenance sector is most popular due to its non hazardous emulsifying agents. Cold wash effectively cleans greasy soiled mass from surface as well as machinery parts.
We are one of popular supplier of cold wash in INDIA - Mumbai, Kandla - Gandhidham, Chennia - Ennore, Visakhapatnam - Gangavaram, Kolkata - Haldia - Paradip. And in Middle East - Dubai - Fujairah - Sharjah.
We have new advanced formulation of COLD WASH chemicals, Which is more effective and powerful. New Generation Product - NEW ORG ( http://www.rxmarine.com/new-org )
India - mail@rxmarine.com
Middle East : dubichem@rxmarine.com
COLD WASH developed to clean any oily and greasy surface by simple cleaning method. By spraying neat undiluted Coldwash onto the surface of oily greasy components to be cleaned is also one of simple cleaning uses method of cold wash. Cold wash also emulsify and remove most of mineral oils and fats from cargo and storage tanks.
Cold Wash is classified Cleaning Chemicals and degreaser. Due to the presence of heavy-duty emulsifying agent in selected solvents, its penetration power on soiled greasy and oily mass becomes very effective this is the reason why coldwash is one of important part in Cleaning and Maintenance group of chemicals. We selected biodegradable emulsifying agent in COLD Wash to makes handling easy.
We are one of largest cold wash supplier in Mumbai, Kandla - Deen dayal port, Mundra, Surat, Visakhapatnam - Vizag, Gnagavaram, Manglore, Chennai - Ennore, Kolkata - Haldia, Paradip, Fujairah - Dubai - Sharjah.
If the cooling system is contaminated with oil, fat and other greasy deposits then simply make 100 ltr solution of cold wash with water by the proportion of 10 Ltr Coldwash in to 100 Ltrs water ( or depend on contamination of oil deposits on the surface, cold wash ratio can vary 5 10% in freshwater ). Then circulate emulsion ( prepared solution of the cold wash with water ) for 8 - 12 hrs. And if solution temperature can maintain 50 - 60 degree, then cleaning performance can be increased within a short period of time. Finally, drain all soiled cleaning liquid followed by fresh water until outcome water remains clear.
Cleaning of the cooling system becomes compulsory when system required DESCALING, removal of scale deposits. As oily surface doesn't allow descaler to react with lime deposits.
COLD WASH developed to clean any oily and greasy surface by simple cleaning method. By spraying neat undiluted Coldwash onto the surface of oily greasy components to be cleaned is also one of simple cleaning uses method of cold wash. Cold wash also emulsify and remove most of mineral oils and fats from cargo and storage tanks.
Cold Wash is classified Cleaning Chemicals and degreaser. Due to the presence of heavy-duty emulsifying agent in selected solvents, its penetration power on soiled greasy and oily mass becomes very effective this is the reason why coldwash is one of important part in Cleaning and Maintenance group of chemicals. We selected biodegradable emulsifying agent in COLD Wash to makes handling easy.
We are one of largest cold wash supplier in Mumbai, Kandla - Deen dayal port, Mundra, Surat, Visakhapatnam - Vizag, Gnagavaram, Manglore, Chennai - Ennore, Kolkata - Haldia, Paradip, Fujairah - Dubai - Sharjah.
USES:
Deep cleaning of outdoor condenser coils to restore efficiency and increase performance of the system.
DILUTION RATIOS:
Because RXSOL-41-8672-025 is highly concentrated, it must be diluted prior to use. Dilution also improves penetration into the coil and increases product performance. Actual dilution ratios will vary according to the application. The following is intended as a general
guideline:
- Up to 8-10 parts water to 1 part RXSOL-41-8672-025 coil cleaner for light cleaning and brightening, when expanding foam is not required.
- 3-5 parts water to 1 part RXSOL-41-8672-025 coil cleaner on difficult cleaning tasks.
- 1-2 parts water to 1 part RXSOL-41-8672-025 coil cleaner for use as a high foaming,aluminum finned, air cooled condenser coil cleaner.Use the minimum concentration required to accomplish your task.
Note: Do not use RXSOL-41-8672-025 coil cleaner at concentrations greater than 1:1 (less than 1 part water to 1 part RXSOL-41-8672-025 coil cleaner. Rinse the treated surfaces as well as the surrounding area thoroughly after use.
APPLICATION METHODS:
Low pressure, acid resistant tank sprayers are recommended.
Regardless of application method, avoid inhalation of mist or contact of liquid or mist with skin.
SUGGESTED INSTRUCTIONS FOR USE:
- When handling RXSOL-41-8672-025 coil cleaner or any other strong chemical, be sure to wear chemical imperviousgloves,apron and splash goggles.
- Determine required dilution ratio for the specific application. It is recommended to start with a dilution ratio of 10:1 and increase concentration until the desired results are achieved.
- As with mixing all acids, place the desired amount of water into the tank and then add RXSOL-41-8672-025 coil cleaner
- Turn off fans and allow hot coils to cool before applying.
- Using plain water, wet both the condenser coil as well as the area surrounding the equipment. Wetting the coil with water aids in product penetration and performance.
- Apply the properly diluted product to the coil surface. Whenever possible, apply solution from the outlet side of the coil. Allow product to remain on surface, normally 5-10 minutes. Do not allow product to dry on the coil. Note: In extreme cases, application may have to be repeated to achieve desired results.
- If foaming does not occur, check for extreme grease buildup which will slow cleaning process. Foaming may not occur if coil is coated or painted.
- Rinse coils, tools and surrounding area thoroughly after completing the coil cleaning process
USES:
Deep cleaning of outdoor condenser coils to restore efficiency and increase performance of the system.
DILUTION RATIOS:
Because RXSOL-16-1697-005 is highly concentrated, it must be diluted prior to use. Dilution also improves penetration into the coil and increases product performance. Actual dilution ratios will vary according to the application. The following is intended as a general
guideline:
- Up to 8-10 parts water to 1 par tRXSOL COIL CLEANER for light cleaning and brightening, when expanding foam is not required.
- 3-5 parts water to 1 part RXSOL COIL CLEANER for foaming action on difficult cleaning tasks.
- 1-2 parts water to 1 part RXSOL COIL CLEANER for use as a high foaming,aluminum finned, air cooled condenser coil cleaner.Use the minimum concentration required to accomplish your task.
Note: Do not use RXSOL-16-1697-005 at concentrations greater than 1:1 (less than 1 part water to 1 part RXSOL-16-1697-005 ). Rinse the treated surfaces as well as the surrounding area thoroughly after use.
APPLICATION METHODS:
Low pressure, acid resistant tank sprayers are recommended.
Regardless of application method, avoid inhalation of mist or contact of liquid or mist with skin.
SUGGESTED INSTRUCTIONS FOR USE:
- When handling RXSOL-16-1697-005 or any other strong chemical, be sure to wear chemical imperviousgloves,apron and splash goggles.
- Determine required dilution ratio for the specific application. It is recommended to start with a dilution ratio of 10:1 and increase concentration until the desired results are achieved.
- As with mixing all acids, place the desired amount of water into the tank and then add RXSOL-16-1697-005.
- Turn off fans and allow hot coils to cool before applying.
- Using plain water, wet both the condenser coil as well as the area surrounding the equipment. Wetting the coil with water aids in product penetration and performance.
- Apply the properly diluted product to the coil surface. Whenever possible, apply solution from the outlet side of the coil. Allow product to remain on surface, normally 5-10 minutes. Do not allow product to dry on the coil. Note: In extreme cases, application may have to be repeated to achieve desired results.
- If foaming does not occur, check for extreme grease buildup which will slow cleaning process. Foaming may not occur if coil is coated or painted.
- Rinse coils, tools and surrounding area thoroughly after completing the coil cleaning process
USES:
Deep cleaning of outdoor condenser coils to restore efficiency and increase performance of the system.
DILUTION RATIOS:
Because RXSOL-41-8672-025 is highly concentrated, it must be diluted prior to use. Dilution also improves penetration into the coil and increases product performance. Actual dilution ratios will vary according to the application. The following is intended as a general
guideline:
- Up to 8-10 parts water to 1 part RXSOL-41-8672-025 coil cleaner for light cleaning and brightening, when expanding foam is not required.
- 3-5 parts water to 1 part RXSOL-41-8672-025 coil cleaner on difficult cleaning tasks.
- 1-2 parts water to 1 part RXSOL-41-8672-025 coil cleaner for use as a high foaming,aluminum finned, air cooled condenser coil cleaner.Use the minimum concentration required to accomplish your task.
Note: Do not use RXSOL-41-8672-025 coil cleaner at concentrations greater than 1:1 (less than 1 part water to 1 part RXSOL-41-8672-025 coil cleaner. Rinse the treated surfaces as well as the surrounding area thoroughly after use.
APPLICATION METHODS:
Low pressure, acid resistant tank sprayers are recommended.
Regardless of application method, avoid inhalation of mist or contact of liquid or mist with skin.
SUGGESTED INSTRUCTIONS FOR USE:
- When handling RXSOL-41-8672-025 coil cleaner or any other strong chemical, be sure to wear chemical imperviousgloves,apron and splash goggles.
- Determine required dilution ratio for the specific application. It is recommended to start with a dilution ratio of 10:1 and increase concentration until the desired results are achieved.
- As with mixing all acids, place the desired amount of water into the tank and then add RXSOL-41-8672-025 coil cleaner
- Turn off fans and allow hot coils to cool before applying.
- Using plain water, wet both the condenser coil as well as the area surrounding the equipment. Wetting the coil with water aids in product penetration and performance.
- Apply the properly diluted product to the coil surface. Whenever possible, apply solution from the outlet side of the coil. Allow product to remain on surface, normally 5-10 minutes. Do not allow product to dry on the coil. Note: In extreme cases, application may have to be repeated to achieve desired results.
- If foaming does not occur, check for extreme grease buildup which will slow cleaning process. Foaming may not occur if coil is coated or painted.
- Rinse coils, tools and surrounding area thoroughly after completing the coil cleaning process
Question :
From Scorpio Operations Supramax Bulk.
One of our Ultramax vessels is calling Deendayal (ex-Kandla) for discharge of coal and we are looking to supply chemicals to clean holds for next cargo which is Urea. Please revert with products; competitive rates; etc.
Best regards
Mrs Prabha Suvarna, Scorpio Marine Management Pvt. Ltd (as agents only).
Answer :
RX Tuff Extra foam Cleaning detergent effectively cleans coal dust and powder from hold surface area by using simple either by high pressure/ low pressure machine. But if question come to load for clear cargo like urea then one tricky option is most common by experienced person. First of all mix water with RX Tuff High Foam (A = 1 Ltr RX Tuff High Foam and 10 Ltrs Water ) Then use equal proprtion of Stabilized sodium Hypo chlorite in to the " A " solution to make " B " solution. Then follow general Cleaning Tips -
The hold cleaning process can be made easy by adopting these 3 steps-
First of all clean entire area by dry sweeping, this will not only helps to get cargo ready fast but also helps to reduce cleaner quantity requirements.
Then apply " B " chemical cleaner to reacts or neutralised residue content.
Finally high-pressure water wash will help to get optimum results.
Coal Stain cleaning is difficult with ordinary cleaner. Our regular work with such residues given us opportunities to make its cleaning easy without scrubbing.
Our RX TUFF High foam cleaner is principally based on Alkaline emulsifiers.
Coal remover may be used concentrated or diluted with water, depending on the degree of contamination, the surface area to be treated, the desired degree of cleaning and the available downtime. Actually, the user is the best one capable to regulate the quantity and concentration to be used for the situation at hand. In any case, when the accumulation is not heavy, a 50% solution with water must be used. Otherwise, Coal Remover can be used undiluted especially when the deposition is heavy and hard spots persist.
Cleaning Procedure
Conventional cleaning methods such as a brush, hard sponge, thick and hard broom and /or a mop can be used on heavy-duty and hard stain deposits. Note that for heavy accumulations the cleaning procedure might be necessary to be repeated until the results are satisfactory. Furthermore, is important to keep in mind that 1 litre of Coal Remover is sufficient to cover a surface area of 8–10 square meters.
NOTE ::: -- Let this product soak into the surface for 30-45 minutes. Then using a high-powered spray washer blast the surfaces until the stains and discolouration is gone.
A water-based heavy duty alkaline Coal cleaner is helpful for removal of stains of coal. Also contains a specialized blend of synthetic. surfactants The cleaning should take place as soon as the discharge is complete to maximize effectiveness.
Feel free to share your furhter querry thorugh email : mail@rxmarine.com
Coal Remover Stock Point : Mumbai. Kandla, Mundra, Chennai Ennore, Visakhapatnam, Gangavaram, Kolkata, Haldia, Dhamra, Paradip, Muscat, Fujairah UAE