1. Is the product for removal of hard water scale.? When applied on the effected areas how much it will be get removed. about thickens of the film or suggest us the right procedure for removal of thick & minor accumulations. also suggest for right application procedure.  

Ans : Quantities of descaler is directly depends up on quantities of mineral scale, This product chemically dissolve SCALE. Scale is a composite mixture of mineral deposits which can be dissolve by using descaler. For application and using procedure pl. visit our product manual.

2. Does it harm full for humans.

Ans : This product contain acidic component along with buffer and corrosion inhibitor, So precaution required before handling of this product.

3.Can it will be used in closed rooms like bath rooms & Labs, or you suggest something else for this type of applications.  
Ans : This product is without fumes, So it can be use in closed room.

4.We are requesting to get clarify this from concerned technical / chemical person to avoid any hazard.at our end. ::: Before uses of this product, You must read MSDS.

Total dissolved solids in Alkali cleaner - includes all solids present in a Alkali Cleaner. Determined by evaporating in a 105 oC oven for 24 hours to evaporate the liquid solution.

Procedure:

Weigh an evaporation dish to the nearest 0.1 mg. Accurately measure a known volume (as much as will fit without spilling) of your sample into an evaporation dish and place in the 105 oC oven for 24 Hrs. After all of the Liquid has evaporated, let the dish cool in a desiccator, weigh the dish plus the remaining solids and record.

Calculation of solids by differentiating "A" and "B" 

A = weight of dried residue + dish after 24 hrs at 105 oC (mg) 

B = weight of dish (mg) 

Finally, percentage mass can be calculated accordingly.

Alkleen Liquid plays very important role for cleaning of tanks, specially when cargo containing fats and oil. Alkleen Liquid effectively emulsify oily mass with water to get dissolve into water. Due to its non caustic based formula Alkaleen Liquid uses becomes wide and non corrosive towards metal surface. Alkleen liquid formulated with corrosion inhibitor to increase its suitability towards tank metal surface, Chemical expert claims that long duration of CARGO in a tank ionized the metal surface. Any chemicals contact can directly damage the metal surface, So presence of corrosion inhibitor in Alkleen cleaner results protection towards tank surface.

Alkleen Liquid supplier in Ennore - Chennai, Vizag - Visakhapatnam - Gangavaram, kolkata - haldia - Paradip, Mumbai - JNPT, Gandhidham - Kandla - Mundra - Sikka, Fujairah - Dubai- Sharjah - Abu dhabi.

Alkleen Liquid available packing is in 20, 25, 50, 210 Ltr

Alkaline Cleaner helps to emulsify and clean  vegetable oil, Fish Oil, Animal Oil and Fatty acid containg cargo from tanks ( Steel and Epoxy )

Email : mail@rxmarine.com

Alkleen Liquid concentrate tank cleaner formula principally developed for emulsification of vegetable, animal and fish oils, drying, semi-drying and non-drying natural oils and fats etc, Alkleen Liquid emulsifying agents and other surfactants are biodegradable and water soluble in nature. Alkleen Tank Cleaner also Can be used for hydrocarbon freeing of cargo tanks. 

As we observed that Alkleen powerful emulsification also resulting to clean tank from black to white.  Alkleen Liquid emulsify easily oil and grease deposits which helps to clean heavy duty deposited cargo from tank, this is the reason why ALKLEEN LIQUID is popular as a tank cleaner.

Mail us to get specialized technical suggestion and easy delivery of Alkleen Liquid in INDIAN and Middle East Port : alkleenliquid@rxmarine.com

OTHER USES

ALKLEEN conncentrate Liquid also helpful for removing oil, carbon and greasy compounds from steam sides of condensers and heat exchangers, Steam Jennys or steam guns etc... Also effectlvely cleans removing oil from the water side of boilers.

Multi Clean Tank Wash Detergent Using-Procedure:- 

First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method is by direct injection followed by recirculation washing, using tank cleaning machines.

Spraying Method:- Spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages.  Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry.

**Make sure to take all safety precautions are followed when handling / spraying as other  GENERAL TANK CLEANER **

Injection Method:- Not applicable. 

Re- Circulation Method:- Fill tank with fresh water and heat up to warm 50oC .  IF a drop line is available on the tank line system, then start to circulate the water and add the required amount of Caustic flakes and MULT CLEAN to make a 2.5% solution.  A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank.  Under normal circumstances, between 2.5% and 4.5% will be sufficient strength.  If there is no drop line, then lower butterworth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material. 
 

**Use a strainer at the pump stack when circulating any solution.**  Tank Lining– Stainless / Epoxy / Phenolic.

What is procedure to cleam Lime from ship hold surfaces?

LIME REMOVER HD  is concentrated liquid product specifically engineered to attack, penetrate and remove lime deposit from cargo hold. It is a liquid product designed to Clean and eliminate limestone caustic lime deposits and dry lime stains from cargo.

Best results can obtain on dry surface of LIME.  It break down the ionic bond in lime, releasing the lime from any surface to which it has adhered.

Lime Remover HD must be used according to the hold surface area that is to be covered, the extent of contamination, the available downtime and the application method being used. Lime Remover HD is covering 10-12 Squire Meter area.

Using Procedure

I - Spray Method

Spray Method is applicable where spray machine is available, suitable to process chemical solutions, is used with a 50% Lime Remover HD/water solution to SPRAY directly onto the surface area. Then, the solution must be left to act for 15 minutes followed by thorough rinsing using a high–pressure water supply source. After , the surface must be left to dry. The percentage  of dilutions may vary depending on the thickness and hardness of the deposited lime.

II – Soaking Method

Soaking is a method where Lime Remover HD is used undiluted and applied with conventional methods such as an elongated thick and hard brush, a hard sponge etc. Once applied, Lime Remover HD must be left to soak for 30 minutes. Rinse with water, and followed by leaving the surface to dry. Usually, this method is applicable to heavily contaminated small and large tank surface areas and installations.

To get more details of Lime wash clenaing chemicals, Please share your querry through our email address mail@rxmarine.com 

We are one of largest Lime remover and other hold cleaning detergent manufacturer and supplier in Paradip, Haldia, Kolkata, Hazira, Navlakhi, Kandla, Mundra, Dharamtar, JNPT Mumbai, Fujairah, Muscat, Barka, Chennai, Ennore, Visakhapatnam, Kakinada

Lime Remover available in 25 Ltrs / 50 Ltr / 210 Ltrs packing with Quality protected Sealed container.
Lime Remover also helpful to clean CEMENT deposits.

WhatsApp No : 0091 9821214367 ( Feel free to get direct Technical Support for Lime Remover and many other hold cleaning detergent )

Query ::: 
Moncy Thomas

Attachments12:51 PM (21-03-2018)

to RXSOL, 123 

Dear sir, 

Good day 

Please note that our last discharging cargo is  STEAM (NON-COKING) COAL IN BULK OF INDONESIA ORIGIN, pls confirm  the Chemical- Sodium Hypochlorite solution(12%)  is for removing  coal  residue,  not cement bulk etc..

Kindly consider your rate and reply us urgently. 

Matter is most urgent for us. 

Awaiting your prompt and valued reply. 

Thanks & Regards 

Mr. Moncy Thomas / Jitu

Solution :

GD DAY.

As per our experience and general practises we observed that cleaning of STEAM coke becomes very easy and more effective by following this cleaning method...

1st Step spray Sodium Hypo on the entire surface area then continuously followed by Aquatuff High Foam ( dilution ratio 1 Ltr Aquatuff High Foam with 20 Ltr Water). Chemically Sodium Hypo Soften coal deposited particle, while Aquatuff resulting excessive foam with super detergency cleaning action which is resulting in the more satisfactory result.

Thanking you

WBRGDS
Kiran

Malara Group - Kailash.S

Dear Mr. Tiwari,

Kinldy suggest RXSOL hold cleaning chemicals for  below details:

Last cargo: grain/bale

Hold size: approx. 15500 cbm (20m x 18m)

No. of hold: 3

Kindly advice suitable grade of chemical as per above specification & approx. quantity require per hold.

Awaiting yours….

Tks & Brgds,

KAILASH H. SONI

DY.G.M.(ADMIN)

MALARA SHIPPING PVT. LTD.

::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::

Answer :-

RXMARINE.com mail

to Malara, rxmarine.com, a.j

Dear Sir,

GD DAY.

Thanks a lot for your inquiry, SUITABLE and most common product to clean FOOD GRAIN is alkleen Safety Liquid. Which is very effective to clean grain deposited stain and masses. Kindly refer the link to get more information of product http://rxmarine.com/Alkaatuff-emulsifier-liquid-alkaline-ship-cargo-hold-cleaning-marine-chemical-detergent-manufacturer-supplier-exporter

And materials required for Each cargo cleaning is approx 200 Ltr. And to clean all 3 cargo required materials quantity is 600 Ltr.

Stock is available at  : http://rxmarine.com/where-to-buy.

Iron Ore Red Dust Cleaner Usage Directions 
Directions for Use 
In general  Dilute 1 part Iron Ore Red Dust Cleaner with 4 parts water and spray  onto the surface being cleaned, And allow Iron Ore Red Dust for 20 to 40 Minutes to penetrate. 
And For Hard Deposits Vigorously agitate the on the surface being cleaned with a stiff bristled brush or broom. And allow Iron Ore Red Dust for 20 to 40 Minutes to penetrate. Again, vigorously agitate the surface. The iron ore will begin to break up and be released from the substrate. 

Stubborn areas may need to be again saturated and left for a further 10 minutes before vigorously agitating. 
Rinse the surface with a high pressure washer or hose until all dissolved concrete and Iron Ore Red Dust Cleaner has been removed from the surface being cleaned. 
Test Iron Ore Red Dust Cleaner on a small inconspicuous area before use. 
Do not apply Iron Ore Red Dust Cleaner undiluted. 
A more concentrate dilution may be required where concrete has been cured for an extended period of time. 
Do not leave Iron Ore Red Dust Cleaner on any surface for extended periods of time. 
To maintain product integrity, keep container sealed when not in use. 

A Simple Test to separate Ethanol and its unwantingly added water is to add POTASSIUM CARBONATE to separatethem out. This offers a very small potassium carbonate impurity to the alcohol that can be removed by distillation. This method is very useful in purification of ethanol by distillation, as ethanol forms an azeotrope with water.